June 28, 2017, 06:22:05 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Thom9mil

Pages: [1]
1
Had the bushing in the cocked position and had inserted the barrel. Not sure how but the next thing I know I'm doing the ouchy dance with the slide hanging off my finger.
Was going to post a picture of my fingert but can't seem to figure out how to put pictures in. I keep getting messages the
 message below. the picture file is only 93k so not sure what is going on.

Your attachment couldn't be saved. This might happen because it took too long to upload or the file is bigger than the server will allow.

Please consult your server administrator for more information.

2
A good day at the range. Little R51 ran flawless as usual. Was a great time.
Got home and stated cleaning the little fella...my nemesis with the R51.
My fingers slipped on reassemble and the next thing I know I'm wearing a slide on my little finger. So after saying ouch and a few not so polite words I got the dumb thing off. 2 soaked bandaids and an hour later it was back together. Moral of the story....keep all appendages away from that spring and the ejection port.

3
R51 General Discussion / Re: remington r51 grips
« on: May 17, 2017, 04:00:15 AM »
Nice looking grips.

4
R51 General Discussion / Re: Feeding Problems
« on: May 14, 2017, 03:37:53 AM »
I've been enjoying faultless operation. :)

5
General Discussion / Re: Just got it back
« on: April 20, 2017, 11:45:27 PM »
Glad to hear they put you on the happy road. I've put several hundred rounds through mine with no jams, fail to eject or any other nuisance activities.
My sights were off by about 4" right and 4" low at 9 yards. Resolved this myself with a new front sight from Dawson's and a dial indicator to center up the lefty right stuff. All is good now.
I am about 100 rounds away from calling it ready to find a good defensive load. Looking at the Remington HTP. I think those are either 124 grain or 147 grain. Would prefer heavier but will be happy with what the R51 likes.
Enjoy. It is a hoot to shoot.

6
R51 General Discussion / Re: Trijicon tritium sights for the R51
« on: April 14, 2017, 07:18:53 AM »
It is Dawson SKU: 020-434-00.
https://dawsonprecision.com/novak-cut-fiber-optic-front-sights/

$39 shipped. You will need a needle file to take a few strokes on the new sight with. Ships with a small punch that has been cut for addressing the sight. I used a sight pusher. Took about 10 minutes. I spent more time with a dial indicator to get it lined up.

7
R51 General Discussion / Re: Trijicon tritium sights for the R51
« on: April 13, 2017, 08:36:43 AM »
I'm happy with .130 front sight height. I installed a fiber optic from Dawson Precision. A few strokes with the file and it fit perfect. Strokes on the new sight of course.

The 2 flyers low and left was me getting settled. Then aimed for red dot at 9 then finally at center. 9 yards.

Red lock tight applied. I ran another 50ish rounds today. Again like before -- no FTF, FTE or FTRB.

I'm happy.

After multiple attempts to attach a photo I give up. Sorry folks.


8
R51 General Discussion / Re: Trijicon tritium sights for the R51
« on: April 10, 2017, 05:27:57 AM »
Yes a shorter front sight is ordered.
Knock on wood I'll have this today or tomorrow and will have some range time on Thursday.

9
R51 General Discussion / Re: Trijicon tritium sights for the R51
« on: April 08, 2017, 10:24:48 PM »
Still a no go with elevation using the military hold. This little fella is about 4 inches low. Sigh.
New front site ordered. We'll see.

10
R51 General Discussion / Re: Trijicon tritium sights for the R51
« on: April 05, 2017, 10:51:41 PM »
I'll give this a try today. If this pans out -- cool. Thanks.

11
R51 General Discussion / Re: Trijicon tritium sights for the R51
« on: April 04, 2017, 08:29:22 AM »
I might have to give those a try. Mine is shooting low and right. I think I have the right portion solved (range time on Thursday) but would like to get the elevation portion solved also.

Did this come with install tools or do I need to take to a gunsmith? Thanks.

12
R51 General Discussion / Re: Take down of R51 made easy.
« on: April 04, 2017, 08:27:35 AM »
I tried this. Worked great in the take down stage. Still had a dickens of a time putting it back together......sigh. I'll get the hang of it. Next range time is Thursday so another learning opportunity presents itself.http://r51pistol.com/Smileys/default/cool.gif

13
Remington R51 Facts and Specs / Re: Desantis Sof-Tuk holster
« on: April 02, 2017, 10:27:57 PM »
I see  Winthrop is carrying leather IWB and OWB for the R51. Nice. My favorite "less expensive" holster company.
http://www.winthropholsters.com/search.php?search_query=r51&Search=

Pages: [1]